Huawei RRU3232 Installation Manual Download Page 63 | Manualshive

Page: 63 / 95

background image

1.

After climbing up to the tower, installation engineer A secures the fixed pulley to the tower
platform support and leads the lifting sling through the fixed pulley.

2.

Installation engineer C binds the RRU and mounting kits using the lifting sling and secures
the traction sling to the RRU handle.

3.

Installation engineer B pulls the lifting sling downwards, and installation engineer C pulls
the traction sling outwards to protect the RRU and mounting kits from colliding with the
tower.

4.

Installation engineer A catches the RRU and mounting kits and then unties the sling.

NOTE

The procedure for hoisting the RRU and mounting kits onto the tower is for your reference only.

----End

RRU3232
Installation Guide

6 Installing the RRU

Issue 05 (2011-10-20)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

55

«
...
61
62
63
64
65
...
»

Summary of Contents for RRU3232
































































































Reviews:

No comments

Related manuals for RRU3232

Brand: YOKOGAWA Pages: 12

Brand: Vega Pages: 20

Brand: Vega Pages: 88

Brand: Vega Pages: 28

Brand: Vega Pages: 92

Brand: Warrior Winches Pages: 17

NNC994S - Genius Prestige - Convection Microwave...

Brand: Panasonic Pages: 1

Brand: KEDO Pages: 2

Brand: KEDO Pages: 3

Brand: KEDO Pages: 2

Brand: R&G Pages: 22

Brand: R&G Pages: 8

Brand: Ikelite Pages: 28

Brand: Logik Pages: 52

Brand: Balt Pages: 8

Brand: moon Pages: 4

Brand: NATIVE UNION Pages: 3

Solar Shade 200

Brand: Dometic Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands