Huawei OceanStor 5300 V3 Quick Installation Manual Download Page 22

Page: 22 / 25

Checking status indicators on the enclosures

After powering on the controller enclosure and disk enclosures, check the Alarm/Location indicators of disks.



If the Alarm/Location indicator of a disk is steady red, contact Huawei technical support.



If all Alarm/Location indicators are off, all disks are running correctly.

Controller enclosure

Pressing the power button on the controller enclosure

Power indicator of the controller

enclosure: steady green

Alarm indicator of the
controller enclosure: off

Controller enclosure

NOTICE

Power indicator of the

disk enclosure:

steady green

Alarm indicator of the
disk enclosure: off

Alarm/Location indicator
of the disk module: off

Disk enclosure

Alarm indicator of the
disk enclosure: off

Power indicator of the disk

enclosure: steady green

Disk enclosure

Alarm/Location indicator
of the disk module: off

Summary of Contents for OceanStor 5300 V3


























Search results

Summary of Contents for OceanStor 5300 V3

Reviews:

Related manuals for OceanStor 5300 V3

Brands by name

Popular brands

Huawei OceanStor 5300 V3, Quick Installation Manual

Search results

Summary of Contents for OceanStor 5300 V3

Reviews:

Related manuals for OceanStor 5300 V3

Brands by name

Popular brands