Huawei OceanStor 18500 V3 Features Manual Download Page 174 | Manualshive

Page: 174 / 183

background image

A

Using the External Storage System to

Perform Initial Synchronization for a Remote

Replication

You can perform initial synchronization for a remote replication using the external storage
system.

NOTICE

This section is intended for Huawei technical engineers. Use this method only under the
guidance of Huawei technical engineers. If you want to use this method to perform initial
synchronization, contact Huawei technical support engineers for help.

A.1 Introduction

After a remote replication is established between the production center and the DR center,
initial synchronization is automatically started to replicate data from the production center to
the DR center.

A.2 Configuration Operation (Using the LUN Copy Feature of the External Storage System)

You can create a LUN copy on the external storage system to implement initial
synchronization for a remote replication.

A.3 Configuration Operation (Using the LUN Copy Feature of the Production and DR
Centers)

You can create a LUN copy on the storage system of the production center and DR center to
implement initial synchronization for a remote replication.

A.1 Introduction

After a remote replication is established between the production center and the DR center,
initial synchronization is automatically started to replicate data from the production center to
the DR center.

In actual application scenarios, the amount of data in the production center is large (up to a
terabyte level), but the data transmission bandwidth is limited between the DR center and the

OceanStor V3 Series
Remote Replication Feature Guide for Block

A Using the External Storage System to Perform Initial

Synchronization for a Remote Replication

Issue 06 (2018-01-30)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

166

«
...
172
173
174
175
176
...
»

Summary of Contents for OceanStor 18500 V3
























































































































































































Reviews:

No comments

Related manuals for OceanStor 18500 V3

NBX V3000 Analog

Brand: 3Com Pages: 2

OfficeConnect 3C19500

Brand: 3Com Pages: 52

Q.HOME+ESS HYB-G2

Brand: Qcells Pages: 26

Garage Gator GGR125

Brand: V-Bro Products Pages: 17

Azure StorSimple 8100

Brand: Microsoft Pages: 12

StorTrends 1312-P

Brand: American Megatrends Pages: 2

StorNext QD7000

Brand: Quantum Pages: 29

NSLU2 - Network Storage Link NAS Server

Brand: Linksys Pages: 64

Brand: QNAP Pages: 7

DURAMAX METAL GARAGE

Brand: USP Pages: 109

Brand: Galvo Shed Pages: 2

DiskStation Series

Brand: Synology Pages: 6

Beside Storage Pantry

Brand: Haworth Pages: 6

Catalina KC-103

Brand: SPAREHAND Pages: 2

TS-U100 - NAS Server - USB

Brand: TRENDnet Pages: 47

PREMIUM STP7736

Brand: Supatool Pages: 3

SPINPOINT MP4 HM250HJ

Brand: Samsung Pages: 1

Brand: Samsung Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands