Huawei NetCol5000-C030H90D0 User Manual Download

Page: 188 / 206

NO TE

The screen for entering the diagnostic mode:
● Components are interlocked. Therefore, buttons for turning on or off certain

components are in gray, indicating that operations of the components are not allowed.

● To ensure system security, a component may not promptly respond to operations

performed on this screen. For example, the compressor does not respond promptly after

the Off (On) button is tapped if the shortest running (shutdown) time is not met.

● To exit the diagnostic mode, tap

on the status bar.

● The system automatically exits diagnostic mode when it reaches the maximum

diagnostic mode duration.

Step 2 Set Indoor fan to 50%.

NO TICE

For safe system operation, when smart cooling product components are turned on,

the following coupling relationships are presented:
● When the electric heater is turned on, the indoor fans will turn on

automatically.

● When the electrode humidifier is turned on, the indoor fans and inlet water

solenoid valve will start automatically.

● When the input value of the indoor fan is less than the minimum speed, the

indoor fan will run at the minimum speed.

Step 3 Check that the indoor fans run properly, and no alarm generates.

Step 4 Choose Maint > Diagnostic Mode > Exit or tap

to exit the diagnostic mode.

----End

7.1.15 Restoring Factory Settings

Context

If you have forgotten the password or need to restore factory settings, you can

restore factory settings by pressing the SW key on the main control board.

NO TICE

● If you restore factory settings, all system data will be restored to the state

before delivery, including login passwords, operation logs, parameter

configurations, and performance statistics. All historical alarms are also cleared.

Perform this operation with caution as it may affect other users.

● To ensure information security and prevent malicious password reset, you must

keep the cabinet keys securely.

NetCol5000-C(030, 032, 065) In-row Chilled Water

Smart Cooling Product

User Manual (2019)

7 FAQ

Issue 03 (2020-08-30)

180

Summary of Contents for NetCol5000-C030H90D0















































































































































































































Search results

Summary of Contents for NetCol5000-C030H90D0

Reviews:

Related manuals for NetCol5000-C030H90D0

Brands by name

Popular brands

Huawei NetCol5000-C030H90D0, User Manual

Search results

Summary of Contents for NetCol5000-C030H90D0

Reviews:

Related manuals for NetCol5000-C030H90D0

Brands by name

Popular brands