background image

3

 Unpacking and Checking

This section describes how to unpack and check the delivered equipment to ensure that the
materials are complete and intact.

Context

NOTE

The following lists important notes when you are transporting, lifting, or installing the equipment or
components:

l

Protect them from colliding with doors, walls, shelves, or other objects.

l

Wear clean gloves and do not touch them with bare hands, sweat-soaked gloves, or dirty gloves.

NOTICE

You must power on the RHUB or pRRU within 7 days after it is unpacked.

Procedure

Step 1

Count the total number of the shipments.

If...

Then...

The total number of the components is
consistent with that recorded in the
packing lists on all packing boxes

Go to 

Step 2

.

The total number of the components is
inconsistent with that recorded in the
packing lists on all packing boxes

Report the problems and causes to the local
Huawei office.

Step 2

Check the exterior of each packing box.

LampSite
Installation Guide

3 Unpacking and Checking

Issue 02 (2014-05-27)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

7

Summary of Contents for LampSite





































































































Reviews: