manualshive.com logo in svg

Huawei IAD108A, User Manual

The Huawei IAD108A is a versatile communication device that provides seamless connectivity. Unlock its full potential by accessing the user manual, available for free download at manualshive.com. This comprehensive manual offers valuable insights and step-by-step instructions to help you maximize the features and functionalities of your Huawei IAD108A.

Share
Download
background image

User Manual 
U-SYS IAD108 Integrated Access Device 

Chapter 1  System Overview 

 

1-4 

z

 

Test on subscriber line. (optional) 

z

 

Support the power supply from remote place.  

z

 

Support traditional PSTN telephone services, including: 
call forwarding, Caller Identification Display (CID) and call 
waiting. With the right telephone set, voice message 
indicator function can also be provided. 

z

 

Support the supplementary services in coordination with a 
softswitch. 

z

 

Support intelligent services and special applications in 
coordination with a softswitch. 

1.3  

System Structure 

1.3.1  Hardware Structure 

There are indicators on the front panel of IAD108, and their 

names and meanings are as shown in Table 1-2.  

Table 1-2

 

Table of IAD108 indicators 

Indicator Color 

Name 

Meaning 

PWR Green 

Power supply 
indicator 

When local power supply is 
connected, it is on. If there is no 

power supply, it is off. 

When remote power supply is 
connected, it blinks. If there is no 
power supply, it is off. 

RUN Green 

Running 
indicator 

It blinks two times per second when 
loading. 

It blinks one time per second when 
running normally.  

Summary of Contents for IAD108A








































































































































































































































































































Reviews:

No comments

Related manuals for IAD108A

C-Bus 5200PG User Manual preview
5200PG
Brand: C-Bus Pages: 36
Quintum Tenor AX Quick Start Manual preview
Tenor AX
Brand: Quintum Pages: 4
QUNDIS Q gateway 5.5 direct Operating And Installation Instructions preview
Q gateway 5.5 direct
Brand: QUNDIS Pages: 80
WAGO 758-918 Manual preview
758-918
Brand: WAGO Pages: 76
ZyXEL Communications P-324 User Manual preview
P-324
Brand: ZyXEL Communications Pages: 352
Zenitel ICX 500 Mounting & Installation preview
ICX 500
Brand: Zenitel Pages: 14
Everflourish 30UL-WB User Manual preview
30UL-WB
Brand: Everflourish Pages: 4
SIMARINE SN01 User Manual preview
SN01
Brand: SIMARINE Pages: 5
gefran R-ECAT Installation And Operation Manual preview
R-ECAT
Brand: gefran Pages: 2
IEI Technology SEG-1 Installation Manual preview
SEG-1
Brand: IEI Technology Pages: 34
Gempro Technology GP-710 User Manual preview
GP-710
Brand: Gempro Technology Pages: 21
Bryan Boilers UCG Reference Manual preview
UCG
Brand: Bryan Boilers Pages: 56
Alarm Lock AL-IME2-POE Installation Instructions Manual preview
AL-IME2-POE
Brand: Alarm Lock Pages: 8
Alarm Lock AL-IME2 Installation Instructions Manual preview
AL-IME2
Brand: Alarm Lock Pages: 8
SmartRG SR505n Installation Manual preview
SR505n
Brand: SmartRG Pages: 8
Viola Systems arctic c-1220 User Manual preview
arctic c-1220
Brand: Viola Systems Pages: 37
Viola Systems Arctic 3G User Manual preview
Arctic 3G
Brand: Viola Systems Pages: 36
purexx PX-iP Operating Manual preview
PX-iP
Brand: purexx Pages: 50

Brands by name

Popular brands

Load more brands