Bryan Boilers UCG Reference Manual Download Page 1

Page: 1 / 56

Form: 2405

Universal Communication Gateway Reference Manual

Date: 01-25-2019

Revision: 8

Bryan Steam LLC, 783 North Chili Avenue, Peru, IN 46970

Web:

www.bryanboilers.com

Phone:

765.473.6651

Fax:

765.473.3074

E-mail:

[email protected]

Universal Communication

Gateway Reference Manual

The Universal Communication Gateway (UCG) is an external, high performance Building

Automation multi-protocol gateway that is preconfigured to automatically communicate

between Bryan Steam’s products (hereafter called “device”) connected to the UCG and

automatically configures them for BACnet®MS/TP, BACnet IP, Metasys®N2 by JCI,

Modbus TCP/IP or LonWorks®. All Honeywell SOLA, Siemens RWF 40/55, Siemens LMV,

Honeywell RM7800 Series and the Precision Digital Trident PD765 boiler configurations

and Node-ID’s are selected through the UCG Web GUI Configurator for fast and easy

installation. A mix of multiple devices can be used on a single UCG. It is not necessary to

download any configuration files to support the required applications. The UCG is pre-

loaded with tested Profiles/Configurations for the supported devices. This document

provides the necessary information to facilitate installation of the UCG on BACnet

MS/TP, BACnet/IP, Metasys N2 and LonWorks network.

The UCG is provided as a 10” x 12” x 6” NEMA Type 1 control panel that must be

mounted and supplied with 120 VAC. Additional specifications can be found in

Section

Important

If your boiler is equipped with a Bryan Boilers Printed Circuit Board

(WD-857), devices should be pre-wired. See

section 3.1.8

Each boiler device Modbus settings must be configured to

communicate to the UCG.

Summary of Contents for UCG

























































Search results

Summary of Contents for UCG

Reviews:

Related manuals for UCG

Brands by name

Popular brands

Bryan Boilers UCG, Reference Manual

Search results

Summary of Contents for UCG

Reviews:

Related manuals for UCG

Brands by name

Popular brands