Huawei FusionModule1000A20 Installation Manual Download

Page: 95 / 107

FusionModule1000A20 Prefabricated All-in-One Data
Center
Installation Guide

A A Basic Installation Operations

Issue 02 (2020-01-15)

Figure A-5

DPJ end connector

(1) Body

(2) Ferrule

(3) Guarding

(4) Cover lock nut

(5) Plastic-coated metal hose

Preparations

Tools: small cutter, scissors, wrench dedicated for feeder windows, glue gun

Material: sealant

Documents: none

Skill requirement: skilled technician

Procedure

Step 1

Cut the plastic-coated metal hose to facilitate connection between the metal hose and the
ferrule.

Use a small cutter or a pair of scissors to cut the hose at the joint between the
plastic-coated metal hose and the end connector at an angle of 30 to 45 degrees, as
shown in

Figure A-6

Figure A-6

Cutting a hose

Trim any burrs on the cut.

Step 2

Remove the sealant from the DPJ end connector.

Summary of Contents for FusionModule1000A20












































































































Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands

Huawei FusionModule1000A20, Installation Manual

Search results

Summary of Contents for FusionModule1000A20

Reviews:

Related manuals for FusionModule1000A20

Brands by name

Popular brands