Huawei FusionDC1000A Installation Manual Download

Page: 87 / 130

4. Push the sealing plate up at the cabinet side to separate the sealing plate

hook from the sealing plate mounting bracket, and remove the sealing plate.

5. Route the ECC800-Pro 4G antenna cable along the cable tray in the pre-fab.

module to the top of cabinet A1 along the cable chain.

6. Route the ECC800-Pro 4G antenna cable into cabinet A1 through the cable

hole on the top of cabinet A1, route the cable out through the cable manager,

and connect the cable to the 4G antenna port on the ECC800-Pro.

7. Connect the RF_Z antenna cable to the RF_Z antenna port on the ECC800-Pro.

Figure 8-17 Installing the antenna

----End

8.3.3 Installing a PAD

Preparations

The PA should be located beside the main entrance door inside the pre-fab.

module
Tool: Phillips screwdriver
Materials: PAD and PAD charging cable
Skill requirement: common technician

Procedure

Step 1 Adjust the feet at the bottom of the PAD mounting support until they are in the

same width as the PAD. Route the PAD power cable through the cable hole in the

PAD mounting support and then connect the cable to the PAD.

Step 2 Adjust the feet in the upper part of the PAD mounting support and clip the PAD

into the mounting support.

FusionDC1000A Prefabricated All-in-One Data

Center

Installation Guide (IT Scenario)

8 Installing Devices Inside the Pre-fab. Module

Issue 01 (2021-04-20)

Summary of Contents for FusionDC1000A



































































































































Search results

Summary of Contents for FusionDC1000A

Reviews:

Related manuals for FusionDC1000A

Brands by name

Popular brands

Huawei FusionDC1000A, Installation Manual

Search results

Summary of Contents for FusionDC1000A

Reviews:

Related manuals for FusionDC1000A

Brands by name

Popular brands