Huawei FusionCol8000-E240 User Manual Download Page 79

Page: 79 / 305

4.2.4 Cable

NO TICE

● Waterproof connectors for cables should be designed according to the

recommended cable specifications in the following table. If a cable used onsite

does not meet the recommended specifications, the cable may fail to be routed

through the waterproof connector or the waterproof connector may fail to be

secured.

● Table 1 lists the cable parameters under the default power limit of the unit. If

the customer modifies the power limit, determine the appropriate power

distribution capacity of upstream devices (such as cables and circuit breakers)

based on the modified value.

Table 4-4 Cable requirements

Maximum

Current

Item

FusionCol8000-E

140 A

Active input

Recommend

ed cable

cross-

sectional

area

3 x 70 mm

35 mm

Standby input

Recommend

ed cable

cross-

sectional

area

3 x 70 mm

35 mm

NO TE

The onsite grounding resistance must comply with related standards.
When selecting, connecting, and routing cables, follow local safety regulations and rules.
When the external conditions such as the cable layout or ambient temperatures change,

perform verification in accordance with local regulations. The recommended cables are

used only when the following requirements are met:
● The cables are routed over a tray or bracket in a single layer. The distance between

cables must comply with local regulations.

● The AC voltage loss is less than 3%.
● Single- or multi-core 90°C-resistant copper flexible cables are used.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (FDC Scenario)

Issue 02 (2021-04-15)

Summary of Contents for FusionCol8000-E240


















































































































































































































































































































Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands

Huawei FusionCol8000-E240, User Manual

Search results

Summary of Contents for FusionCol8000-E240

Reviews:

Related manuals for FusionCol8000-E240

Brands by name

Popular brands