manualshive.com logo in svg

Huawei FusionCol8000-E24, User Manual

The Huawei FusionCol8000-E24 User Manual is the ultimate guide to help you make the most of your device. Packed with detailed instructions and useful tips, this manual is a must-have for anyone using the FusionCol8000-E24. Download it for free at manualshive.com and unlock the full potential of your Huawei device.

Share
Download
background image

Figure 4-27 FE teamwork group-based ring networking (using 13 units as an

example)

----End

Scenario Switching

Scenario

Operation

Switching from

the independent

wiring scenario to

the shared wiring

scenario

1. Retain the cable connection to the COM/FE port on a

unit, and disconnect the cables from the COM/FE ports

on other units.

NOTICE

Only the cable connection to the COM/FE port on one unit can

be retained. Otherwise, the communication will fail.

2. Set Monitor FE wiring mode to Shared wiring on the

Access Control screen of each unit.

Switching from

the shared wiring

scenario to the

independent

wiring scenario

1. Set Monitor FE wiring mode to Independent wiring on

the Access Control screen of each unit.

2. Connect the COM/FE port on the main control module

of each unit to the FE port on the host.

 

4.5.5 Installing Power Cables

Procedure

Step 1 Route power cables through the external cable holes.
Step 2 Open the electric control box outside the unit.
Step 3 Connect one end of the active and standby power cables to the active/standby

power supply terminals/PE terminal through the cable holes in the electric control

box of the unit, and connect the other end to the power supply.

FusionCol8000-E240 Modular Indirect Evaporative

Cooling System

User Manual

4 System Installation (Building Scenario)

Issue 03 (2021-04-20) Copyright © Huawei Digital Power Technologies Co., Ltd.

60

Summary of Contents for FusionCol8000-E24














































































































































































































































































Reviews:

No comments

Related manuals for FusionCol8000-E24

Makita CL183D Technical Information preview
CL183D
Brand: Makita Pages: 7
Kärcher NT 22/1 Ap L User Manual preview
NT 22/1 Ap L
Brand: Kärcher Pages: 132
Kärcher Puzzi 8/1 C Unit Information preview
Puzzi 8/1 C
Brand: Kärcher Pages: 29
Kärcher NT 40/1 Tact Service Manual preview
NT 40/1 Tact
Brand: Kärcher Pages: 20
Kärcher NT 22/1 Ap L Original Instructions Manual preview
NT 22/1 Ap L
Brand: Kärcher Pages: 212
Kärcher NT 27/1 Original Instructions Manual preview
NT 27/1
Brand: Kärcher Pages: 92
Kärcher K 65 plus Operating Instructions Manual preview
K 65 plus
Brand: Kärcher Pages: 8
Kärcher EB 30/1 Instruction Manual preview
EB 30/1
Brand: Kärcher Pages: 9
Kärcher SV 1902 Instruction Manual preview
SV 1902
Brand: Kärcher Pages: 264
Kärcher SC 3 Premium Original Operating Instructions preview
SC 3 Premium
Brand: Kärcher Pages: 16
Kärcher A 2204 Manual preview
A 2204
Brand: Kärcher Pages: 80
Kärcher SC 1.020 Original Instructions Manual preview
SC 1.020
Brand: Kärcher Pages: 42
Kärcher WV 50 Operator'S Manual preview
WV 50
Brand: Kärcher Pages: 20
Kärcher NT 30/1 Tact Te Instruction Manual preview
NT 30/1 Tact Te
Brand: Kärcher Pages: 204
Team Kalorik TKG SFC 1005 Manual preview
TKG SFC 1005
Brand: Team Kalorik Pages: 52
UFESA AP9000 Instruction Manual preview
AP9000
Brand: UFESA Pages: 62
UFESA AC5010 Operating Instructions Manual preview
AC5010
Brand: UFESA Pages: 31
UFESA AC5000 Instruction Manual preview
AC5000
Brand: UFESA Pages: 26

Brands by name

Popular brands

Load more brands