Huawei CX600-X1-M Series Hardware Description Download Page 53

Page: 53 / 234

2.2.4 AC Power Supply System

The device has two AC rectifier modules working in 1+1 backup mode.

Figure 2-11

shows the

outline of an AC rectifier module.

Figure 2-11

Outline of an AC rectifier module

Table 2-8

Parameters of the AC rectifier modules

Item

Parameter

Dimensions (W x D x H)

183.8 mm x 201 mm x 41.5 mm (7.24 in. x
7.91 in. x 1.63 in.)

Weight

2.5 kg (5.51 lb)

Rated voltage

110 V AC / 220 V AC

Input voltage range

90 V AC ~ 290 V AC

Maximum input current

8 A

Maximum output power

1600 W

Table 2-9

Indicator Description

Indicat
or
Name

Color

Norm
al
Statu
s

Abnor
mal
Status

Remarks

Input
indicato
r

Green

Off

The indicator is on when the input is normal, and is
off when the input is abnormal.

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

2 CX600-X2-M8 Hardware Description

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands