Huawei CX600-X1-M Series Hardware Description Download Page 102

Page: 102 / 234

Item

Specification

Heat
dissipation

32.4 BTU/hour

Weight

0.58 kg (1.28 lb)

Dimensions (H
x W x D)

20 mm x 194 mm x 226 mm (0.79 in. x 7.64 in. x 8.90 in. )

Connector

Earliest
Software
Version

V800R005C01

Product Specifications

Table 4-6

lists the specifications of the 4-Port 10GBase LAN-SFP+ Physical Interface Card

(PIC).

Table 4-6

Specifications of the4-Port 10GBase LAN-SFP+ Physical Interface Card(PIC)

Item

Specification

Supported protocol and
service

Ethernet_II, Ethernet_SAP, Ethernet_SNAP
PTP

Interface type

SFP+

Reliability and availability

Hardware features

Hot-swappable

NMS

Enhanced command line management interfaces
SNMP and MIB

Operating environment

Operating temperature: -40°C to +65°C (-40°F to 149°F)
(Optics used may limit the ambient temperature range)
Long-term relative humidity: 5% to 85%
Short-term relative humidity: 5% to 95%

Storage environment

Storage temperature: -40°C to +70°C (-40°F to 158°F)
Storage humidity: 0% to 95%

4.2 1-Port 10GBase LAN/WAN-SFP+ + 8-Port 100/1000Base-
X-SFP Physical Interface Card(PIC)

HUAWEI CX600-X1-M/CX600-X2-M Series Metro
Services Platform
Hardware Description

4 Boards

Issue 03 (2014-04-30)

Huawei Proprietary and Confidential

Summary of Contents for CX600-X1-M Series











































































































































































































































Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands

Huawei CX600-X1-M Series, Hardware Description

Search results

Summary of Contents for CX600-X1-M Series

Reviews:

Related manuals for CX600-X1-M Series

Brands by name

Popular brands