Huawei CG1-2 Operating Instructions Manual Download Page 19 | Manualshive

Page: 19 / 24

Huawei CG1-2 Operating Instructions Manual Download Page 19

CG1-2A H Beam cutter

- 15 -

4.5

Notice of slanting cutting web plate

1．There is an angle scale plate on the fixed track pressure plate. Track mark allocates on
the specified angle which is locked with nuts. Use nuts to lock. Then fix track and machine
on the H structural section.
2．Slanting cutting is different from line cutting. Torch angle needs to be adjusted, otherwise,
cutting  is  not  whole.  And  some  areas  are  not  cut.  As  shown  in  the  diagram  1.Adjusting
method  is  shown  in  the  diagram  2  and  3.    When  cut  wing  plates,  only  recover  bevel
graduations to zero.

4.6 Bevel cutting operation

When cutting bevel, use the angle (use 5°as its basic unit)on the
torch holder and allocate the torch on an expected angle. When
choosing a tip for bevel cutting, the thickness of the steel plane
is L as shown in following picture. In order to compensate the
over-dose heat loss due to the bevel cutting, the operator should
choose an upper rank tip based on the Cutting Data. Slight

«
...
17
18
19
20
21
...
»

Summary of Contents for CG1-2

























Reviews:

No comments