manualshive.com logo in svg

Huawei 9000 VCT V100R011, Administrator'S Manual, Page: 53 / 204

Share
Download
Huawei 9000 VCT V100R011 Administrator'S Manual Download Page 53

Parameter

Description

Dialing mode

The default value is 

Manual

.

l

Auto

: If this option is selected, the terminal initiates a PPP dial-

up connection automatically. The billing system starts charging
after the dial-up connection is established successfully. If you
use the monthly fee mode, using the automatic mode for the PPP
dial-up connection is recommended.

l

Manual

: If this option is selected, the terminal does not initiate

the PPP dial-up connection automatically. If you pay the fee
based on connection duration, using the manual mode for the
PPP dial-up connection is recommended.

 

Step 2

Save the settings.

----End

2.7.2 Setting 3G Dial-up Parameters and Establishing a Dial-up
Connection

After a PPP dial-up connection is established, the terminal can obtain the IP address allocated
by the server and can make calls over the 3G network.

Prerequisites

Before connecting to the 3G network, ensure that:

l

The terminal is connected with a 3G data card successfully.

l

The 3G network is enabled. For details, see section 

2.7.1 Setting 3G Parameters

.

Procedure

Step 1

Choose 

Settings

 > 

Network

 > 

3G

 > 

3G Dialing

, and then set the parameters listed in 

Table

2-14

.

Table 2-14

 3G dial-up parameters

Parameter

Description

Switch
between 3G
networks

This specifies the 3G network operator.
Click 

Search

 to search for the existing 3G network operators.

USB device

This specifies the type of the data card. The available options are Wideband
Code Division Multiple Access (WCDMA) and CDMA2000.

APN

This specifies the name of the network access point. If a WCDMA data card
is used, you need to set this parameter.
For details, contact your operator.

HUAWEI 9000 HD Video Terminal
Administrator Guide

2 Network

Issue 09 (2012-09-03)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

41

Summary of Contents for 9000 VCT V100R011













































































































































































































Reviews:

No comments