Huawei 50082920 Hardware Installation And Maintenance Manual Download Page 60

Page: 60 / 112

Step 4

To remove an Ethernet connector, press the locking key and pull out the connector, as shown
in

Figure 5-57

Removing an unshielded Ethernet connector

----End

Installing Fiber Connectors

Context

NOTICE

After you remove the dustproof cap, ensure that the fiber pins are clean and install them as
soon as possible.

When you disassemble fiber connectors, you must use a dedicated tool if the connectors
are densely installed.

Cleaning Fiber Connectors

Procedure

Step 1

Clean the pins of a fiber connector by using lint-free cotton and alcohol.

Step 2

Clean the pins again by using dust-free cotton. If necessary, clean the pins by using an air gun.
Ensure that the pins are free from any fiber or debris.

----End

Installing an FC Fiber Connector

R250D
Hardware Installation and Maintenance Guide

5 Appendix

Issue 01 (2016-09-30)

Huawei Proprietary and Confidential

Summary of Contents for 50082920

















































































































Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands

Huawei 50082920, Hardware Installation And Maintenance Manual

Search results

Summary of Contents for 50082920

Reviews:

Related manuals for 50082920

Brands by name

Popular brands