background image

12

Installation prepare

Grounding requirement

1. The air conditioner is the first class electric appliance. It must be properly grounding with 

    specialized grounding device by a professional. Please make  sure it is always grounded 
    effectively, otherwise it may cause electric shock. 

2. The yellow-green wire in air conditioner is grounding wire, which can't be used  for other 

    purposes. 

3. The grounding resistance should comply with national electric safety regulations. 

4. The appliance must be positioned so that the plug is accessible. 

5. An all-pole disconnection switch having a contact separation of at least 3mm in all poles 
    should be connected in fixed wiring. For models with a power plug, make sure the plug is 

    within reach after installation. 

6. Including an circuit break with suitable capacity, please note the following table. Circuit 

    break should be included magnet buckle and heating buckle function, it  can protect the 

    circuit-short and overload. (Caution: please do not use the fuse only for protect the circuit) 

Air-conditioner

Circuit break capacity

Minimum Sectional Area

of Power Cable (mm

2

)

09K

12K

10A

3G1.0

18K

16A

3G1.5

24K

25A

3G2.5

1.

 

 

When installing or relocating the unit, be sure to keep the refrigerant circuit free   

     from air or substances other than the specified refrigerant.

— 

Any presence of air or other foreign substance in the refrigerant circuit will cause system             

     pressure rise or compressor rupture, resulting in injury.

2.

 

 

When installing or moving this unit, do not charge the refrigerant which is not      

     comply with that on the nameplate or unqualified refrigerant.

— 

Otherwise, it may cause abnormal operation, wrong action, mechanical malfunction or 

      

       

even series safety accident.

3.

 

 

When refrigerant needs to be recovered during relocating or repairing the unit, 

     be sure that the unit is running in cooling mode. Then, fully close the valve at high 

     pressure side (liquid valve). About 30-40 seconds later, fully close the valve at low 

To ensure safety, please be mindful of the following precautions.

WARNING

Safety precautions for installing and relocating the unit

Summary of Contents for INNOVA HTWS026INNR32-EXT























Reviews: