background image

 

 

HT7 

 

 

EN - 10 

4.8.  PHASE SEQUENCE INDICATION 

 

 

CAUTION 

 

 

 

  The  maximum  input  for  AC  voltage  is  690V.  Do  not  measure  higher 

voltages  to  avoid  risks  of  electrical  shocks  or  serious  damages  to  the 
instrument. 

 

  symbol  is  lighted  up  whenever  the  voltage  between  the  probes 

exceeds 50V, even if the batteries are low or have been removed. 

 

 

Fig. 6: Phase sequence test 

1.  Perform the preliminary Autotest (see § 4.3). 

 

2.  Connect the L1 probe to phase 1 and the L2 

probe to phase 2 of the three-phase system 
under test (see Fig. 6). The measurement is 
performed 

only  when  probes  are  in 

contact to live conductors.

 

 

3.  The  instrument  turns  automatically  on  and 

the measured AC voltage value is displayed 
both in numerical and bargraph modes

.

 

 

4.  AC  symbol is  displayed.  LEDs 

  and

 

are lighted up for AC voltage measurements 
from 100V to 690V, 50/60Hz

 

5. 

symbol  (clockwise)  and 

symbol 

(counterclockwise)  are  displayed  according 
to the phase sequence detected.

 

 

6.  Connect the L1 probe to phase 2 and the L2 

probe to phase 3 of the three-phase system 
under  test. 

symbol  (clockwise)  and 

symbol (counterclockwise) are displayed 

according to the phase sequence detected.

 

 

7.  Connect the L1 probe to phase 2 and the L2 

probe to phase 3 of the three-phase system 
under  test. 

symbol  (clockwise)  and 

symbol (counterclockwise) are displayed 

according to the phase sequence detected.

 

 

8.  Press  the 

  key  to  switch  on  the  white 

LED illuminator to perform measurements in 
dark environments. 

 

Summary of Contents for HT7

















Reviews: