HS 6200, Installation And Operating Instructions Manual

Page: 10 / 36

with a 3/32” hexagon key wrench. Next, tighten the pivot
screw on the other side of the pivot, with a 1/8” hexagon
key wrench. Now, retighten the set screw to retain the
pivot screw at the new adjustment. Either pivot may be
adjusted.
FIGURE 5
No. 18, 22 Headrest
3.7.3.2. The third adjustment is for proper clearance of the
block dot to indicate that the headrest is properly locked.
If the dot does not fully clear the lock housing when the
headrest is locked securely, turn the set screw located at the
top of the lock housing (Figure 5, item 2) counterclockwise
until the dot on the actuator is fully exposed.
3.7.4. Operation-No. 10 Headrest
3.7.4.1. The No. 10 headrest has a fixed, rigid upholstered
backboard which supports a sliding, center pillow section.
For patient comfort simply move this pillow to a desired
position.
3.7.5. Operation-No. 11, 21 Headrest
3.7.5.1. A single handle on the rear of the No. 11, 21
headrests controls the locking mechanism. To unlock,
grasp the handle and turn counter-clockwise. Change the
tilt of the headrest until it is in the desired position. To lock,
turn the handle clock-wise until snug. (See Figure 6, No. 11
Headrest shown)
PRÉCAUTION : Cette chaise d’examen est
conçue pour utilisation avec un patient
correctement positionné dans la chaise.
Avant d’incliner la chaise, assurez-vous
que le patient est assis dans la chaise et
que la position du patient ne se déplace
pas vers une position extrême soit vers
la tête, soit vers le pied de la chaise,
puisque cela pourrait causer une stabilité
insuffisante
3.6. Footrest
3.6.1. The footrest may be retracted by lifting near its
outer edge. When fully retracted the footstep will stay in
place.
3.7. Headrest
3.7.1. The No. 18 headrest is the standard headrest for
the Model 6200 Chair.
WARNING-
IF THE NO. 18 HEADREST
RECEIVES A IMPACT OR STRIKES AN OBJECT
WITH FORCE CONTACT RELIANCE® TECH
SERVICE IMMEDIATELY.
AVERTISSEMENT : SI L’APPUIE-TÊTE
# 18 REÇOIT UN CHOC OU FRAPPE
UN OBJET AVEC FORCE, CONTACTEZ
IMMÉDIATEMENT LE SERVICE TECHNIQUE
RELIANCE®.
3.7.2. Operation-No. 18, 22 Headrest
3.7.2.1. The No. 18, 22 headrest is designed so it can be
operated with just one hand. To unlock, squeeze the clear
plastic actuator into lock housing. This will allow both pivots
of the articulating arm to rotate so the headrest can be
moved to a new desired position. Once in the new position,
release the actuator. Make sure the actuator expands to its
original position fully exposing black dot on handle to insure a
positive lock. The headrest pad is free to rotate at all times.
(See Figure 5).3.7.3.
Adjustment-No. 18, 22 Headrest
3.7.3.1. There are three adjustments provided on the No.
18, 22 headrest. The first is the tension on the pad rotation.
By tightening the two hex acorn nuts on the pad pivots with
a 3/8” open end wrench, the tension will be increased. To
adjust the drag on the pivots of the articulating arm, loosen
the set screw in the center of the pivot (Figure 5, item 1)
ACORN NUTS
BLACK DOT
ACTUATOR
2
1
IN-6200 10