background image

 

 

Limited Warranty 

 
Harmonic Resolution Systems warrants the product designated herein to be free 
of manufacturing defects in material and workmanship subject to the conditions 
herein set forth, for a period of 90 days from the date of purchase by the original 
purchaser.  If the purchaser registers the unit with Harmonic Resolution Systems 
by mailing in the warranty card, together with a copy of the bill of sale, within 14 
days of the date of purchase, said purchaser would be registered for an extended 
service contract.  The extended service contract extends the 90 days to a period of 
5 years from the date of purchase by the original purchaser or no later than 6 
years from the date of shipment to the authorized Harmonic Resolution Systems 
dealer, whichever comes first.  This warranty is subject to the following 
conditions and limitations. 
 

1.

 

This warranty is subject to the following conditions and limitations.  The 
warranty is void and inapplicable if the product has been used or handled other 
than in accordance with the instructions in the owner’s manual, abused or 
misused, damaged by accident or neglect or in being transported, or the defect is 
due to the product being repaired or tampered with or modified by anyone other 
than Harmonic Resolution Systems.  The product must be packed and returned to 
Harmonic Resolution Systems by the customer at his or her sole expense.  A 
written description of the defect and a photocopy of the original purchase receipt 
must accompany a returned product.  This receipt must clearly list model and 
serial number, the date of purchase, the name and address of the purchaser and 
authorized dealer and the purchase price.  Harmonic Resolution Systems reserves 
the right to modify the design of any product without obligation to purchasers of 
previously manufactured products and to change the prices or specifications of 
any product without notice or obligation to any person. 

2.

 

Warranty does not cover normal recommended care and maintenance. 

3.

 

Harmonic Resolution Systems shall not be responsible in any way for 
consequential or indirect damages or liabilities resulting from the use of the 
product covered herein or resulting from any breach of this warranty or any 
implied warranty relating to said product. 

4.

 

Harmonic Resolution Systems shall not be responsible in any way for damage to 
finishes resulting from normal use and exposure to sunlight and the environment 
even within the normal and extended warranty period. 
 

Summary of Contents for SXR





















Reviews: