HPE ProLiant e910 User And Maintenance Manual Download Page 28

Page: 28 / 182

6. Install the NVMe M.2 SSD.

7. For 2U server blade, do the following:

a. Install the air baffle.

b. Install the top cover.

8. Install the server blade in the chassis.

9. Power up the server blade.

M.2 SSD option

The server blade system board supports NVMe or SATA M.2 SSDs of size 22x42mm or 22x80mm.

Installing the NVMe M.2 SSD

Prerequisites

Before you perform this procedure, make sure that you have the following items available:

• T-10 Torx screwdriver

• Philips No.1 screwdriver

• NVMe M.2 SSD modules

Procedure

1. Power down the server blade.

2. Remove the server blade from the chassis.

3. For 2U server blade, do the following:

28 Hardware options installation

Summary of Contents for ProLiant e910























































































































































































Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands

HPE ProLiant e910, User And Maintenance Manual

Search results

Summary of Contents for ProLiant e910

Reviews:

Related manuals for ProLiant e910

Brands by name

Popular brands