HP Vectra XM 5/120 Series 3 Manual Download Page 29

Page: 29 / 42

3 Troubleshooting and Repair

Using SETUP to Configure the PC

Hard Disk Drives

Drive 1
Drive 2

Interface

Allows you to configure the primary and
secondary hard disk drives.

To define if the integrated IDE controller
is used for the IDE hard disk drive.

None or SCSI/
Custom

Enabled/Disabled

Shows capacity of
the hard disk drive
if one was detected.

Configure any
controller board
according to its
manual.

SCSI BIOS ROM
Address

SCSI BIOS
Shadowing

View the SCSI BIOS ROM address for an
HP SCSI adapter.

To shadow the SCSI BIOS in faster RAM
for HP SCSI adapters.

Enabled/None

Enabled/Disabled

Flexible Disk Drives:

Drive 1
Drive 2

Bootable Drive

Interface

Defines the first and second flexible disk
drives.

Define which flexible disk drive is the
bootable drive.

To define if the flexible disk drive
controller is integrated.

None, 3.5-inch
1.44 MB, or 5.25-
inch 1.2 MB

Drive 1/Drive 2

Integrated/
Controller board

Configure any
controller board
according to its
manual.

Security Features:

System
Administrator
Password

Start with Keyboard
Locked

Start From Flexible
Disk

Start From Hard
Disk

Flexible Disk Drives

Hard Disk Drives

Writing on Flexible
Disks

Plug and Play
Device
Management

Keyboard locked until Password is
entered

Select the level of support for Plug and
Play Accessories (see page 22 for more
details)

Set/Not Set

Enabled/Disabled

None/Boot Only/
Full

Enable when the PC
is used as a Network
Server.

Field Name

Purpose

Options

Remarks

blac-fam.bk : blacfc03.fb4 Page 25 Monday, July 21, 1997 3:59 PM

Summary of Contents for Vectra XM 5/120 Series 3











































Search results

Summary of Contents for Vectra XM 5/120 Series 3

Reviews:

Brands by name

Popular brands

HP Vectra XM 5/120 Series 3, Manual

Search results

Summary of Contents for Vectra XM 5/120 Series 3

Reviews:

Brands by name

Popular brands