manualshive.com logo in svg

HP Vectra XM 5/120 Series 3, Manual

Share
Download
HP Vectra XM 5/120 Series 3 Manual Download Page 23

 

19

2   PC Hardware Structure

Installing Accessories

Installing Video Memory

The HP Vectra XM 5/xx series 3 PC is shipped with 1 MB of video memory 
which can be expanded to 2 MB for resolutions of up to 1024 

✕

 768 in 64K 

colors (see resolutions supported under 

Video Controller

 in chapter 1).

The upgrade kit (D3404A) comprises one module of 1 MB.

Installing an Accessory Board

The HP Vectra XM 5/xx series 3 PC has four slots that can be used for 
installing accessory boards:

❒

the top slot can be used for a half-length PCI accessory board

❒

the second slot can be used for either a full-length PCI or ISA board

❒

the third slot can be used for a full-length 8- or 16-bit ISA board

❒

the fourth (bottom) slot can be used for a half-length 8- or 16-bit ISA 
board.

Accessory boards may have preferred locations and special installation 
instructions - refer to the manual supplied with the board.

blac-fam.bk : blacfc02.fb4  Page 19  Monday, July 21, 1997  3:59 PM

Summary of Contents for Vectra XM 5/120 Series 3











































Reviews:

No comments

Brands by name

Popular brands

Load more brands