HP sv6 Troubleshooting Manual Download Page 27

Page: 27 / 36

troubleshooting your hp visualization center sv6

troubleshooting tree

Chapter 1

✓

Call HP Support and report an sv6 X server problem.

NOTE

Only one graphics card per Workstation is supported for sv6
configurations.

12. sv6 Specific Software Problems

• Graphics software patches must be the same across all master and

slave systems.

❏

If you get version mismatch errors at x server start-up, update
graphics patches on all systems (see sv6 Installation/ Users
Guide).

• Red check marks at X server startup screen.

❏

Check

/etc/X11/X0screens

file for typos or invalid

configurations.

❏

Troubleshoot the first system with a red check mark.

❏

Other check mark colors:

White: Slave system has been contacted
Yellow: Slave has been configured for use in SLS/d or sv6
Blue: Slave X server has been started
Green: Slave X server has been reached and communication has
been established
Red: Error

sv6 startup error and warning messages

Master Error Messages:

•

Duplicate Slave entries detected in X*screens file

Edit

/etc/X11/X0screens

and look for two slave nodes that have

the same hostname.

•

nvalid number of Slaves for current mode of operation.

Run /

opt/graphics/OpenGL/sv/bin/setpipes

to set a screen

layout that is appropriate for your configuration.

•

Bad default visual detected for one or more Slaves.

Summary of Contents for sv6





































Search results

Summary of Contents for sv6

Reviews:

Related manuals for sv6

Brands by name

Popular brands

HP sv6, Troubleshooting Manual

Search results

Summary of Contents for sv6

Reviews:

Related manuals for sv6

Brands by name

Popular brands