HP StorageWorks 2/32 - SAN Switch Installation Manual Download Page 72

Page: 72 / 126

Managing the SAN Switch 2/32

SAN Switch 2/32 Installation Guide

6. At the

Fibre Channel Subnetmask

prompt, enter the address of the

subnetmask, if applicable. Press Enter.

7. At the

Gateway Address

prompt, enter the IP address of the gateway

system if applicable. Press Enter.

The configuration is then committed to the switch firmware.

8. You are then prompted whether to make the IP address changes active now or

at the next reboot. Enter

at the prompt to have the IP address changes take

effect immediately.

Displaying Devices within the Fabric

To verify that you have fabric wide connectivity when you install a new switch,
display the fabric wide device count from the newly installed switch. Use these
steps to display the fabric.

1. Login to the switch as the admin user.

2. At the command line enter the following command:

nsAllShow

This command displays all the connected devices in the fabric.

Checking the Firmware Version

Use these steps to display the SAN Switch 2/32 firmware version.

1. Login to the switch as the admin user.

2. At the command line enter the following command:

version

This command displays the Kernel version, and Fabric OS release number.

Summary of Contents for StorageWorks 2/32 - SAN Switch































































































































Search results

Summary of Contents for StorageWorks 2/32 - SAN Switch

Reviews:

HP StorageWorks 2/32 - SAN Switch, Installation Manual, Page: 72 / 126

Search results

Summary of Contents for StorageWorks 2/32 - SAN Switch

Reviews: