HP StorageWorks 2/32 - SAN Switch Installation Manual Download Page 51

Page: 51 / 126

Installing the SAN Switch 2/32

SAN Switch 2/32 Installation Guide

Connecting the SAN Switch 2/32 to the LAN

Use the following steps to connect the SAN Switch 2/32 to the Ethernet Local
Area Network (LAN) segment.

1. Remove the shipping plug from the SAN Switch 2/32 Ethernet port.

2. Connect one end of an Ethernet cable to the SAN Switch 2/32 Ethernet port;

see

Figure 14

Figure 14: Connecting the Ethernet cable

3. Connect the other end of the Ethernet cable to the workstation or to an

Ethernet network containing the workstation.

Note:

You can now access the switch remotely (and from multiple connections), using

telnet or the Web Tools application. Verify that the switch is not accessed from any other

connections during the remaining steps.

4. Login to the switch with administrative privileges by telnet. The default

administrative logon is

admin

and the default password is

password

SHR-2573A

Summary of Contents for StorageWorks 2/32 - SAN Switch































































































































Search results

Summary of Contents for StorageWorks 2/32 - SAN Switch

Reviews:

HP StorageWorks 2/32 - SAN Switch, Installation Manual, Page: 51 / 126

Search results

Summary of Contents for StorageWorks 2/32 - SAN Switch

Reviews: