HP ML530 - ProLiant - 128 MB RAM Setup And Installation Manual Download Page 93 | Manualshive

Page: 93 / 295

HP ML530 - ProLiant - 128 MB RAM Setup And Installation Manual Download Page 93

Installing Hardware Options

HP ProLiant ML530 Generation 2 Server Setup and Installation Guide

3-47

HP CONFIDENTIAL

Writer: Richard O. Heath File Name: d-ch3 Installing Hardware Options.doc

Codename: Seattle Slew Part Number: 225579-002 Last Saved On: 1/8/03 3:00 PM

The ProLiant ML530 Generation 2 server ships with one hot-plug power supply. The
following procedures show you how to install an optional hot-plug power supply for
redundancy.

To install the redundant hot-plug power supply:

1.

Locate the power supply blank at the rear of the server beneath the system tray.

Figure 3-37: Hot-plug power supplies
(rack configuration)

Table 3-10: Hot-Plug Power Supply Locations

Item Power

Supply

1

Hot-plug power supply 1

2

Hot-plug power supply bay 2 (redundant)

3

Hot-plug power supply bay 3 (not used)*

*Improved power supply performance ensures that a single
power supply provides sufficient power to the entire system.
Complete redundancy can be achieved by installing only one
additional power supply.

2.

Locate and remove the Torx T-15 tool. See “Locating and Removing the
Torx T-15 Tool” in this chapter.

«
...
91
92
93
94
95
...
»

Summary of Contents for ML530 - ProLiant - 128 MB RAM








































































































































































































































































































Reviews:

No comments