manualshive.com logo in svg

HP J4861A, Installation And Getting Started Manual

Share
Download
HP J4861A Installation And Getting Started Manual Download Page 69

B 

Switch Ports and Network Cables 

This appendix includes switch connector information and network cable 
information for cables that should be used with the Series 4100gl Switches, 
including minimum pin-out information and specifications for twisted-pair 
cables. 

N o t  e 

Incorrectly wired cabling is the most common cause of problems for LAN 
communications. HP recommends that you work with a qualified LAN cable 
installer for assistance with your cabling requirements. 

Switch Ports 

Twisted Pair 

■ 

The RJ-45 ports on the 

10/100-TX gl Module

, the 

100/1000-T gl 

Module

, and the on the 

100/1000-T Transceiver

 accept 100-ohm differ 

ential unshielded and shielded twisted-pair cable with RJ-45 connectors 
as described on the next page. 

Fiber-Optic 

■ 

The SC-type connector port on the 

100Base-FX Transceiver

 transmits 

at 1300 nm wavelength, and accepts the multimode fiber-optic cables for 
100Base-FX described on 

page B-3

. 

■ 

The SC-type connector port on the 

Gigabit-SX Transceiver

 and the LC-

type connector port on the 

Gigabit-SX LC mini-GBIC Transceiver 

transmit at 850 nm wavelength, and accept the low metal content, multi-
mode fiber-optic cables for Gigabit-SX described on 

page B-3

. 

■ 

The SC-type connector port on the 

Gigabit-LX Transceiver

 and the LC-

type connector port on the 

Gigabit-LX LC mini-GBIC Transceiver 

transmit at 1300 nm wavelength, and accept the low metal content, single 
mode or multimode fiber-optic cables for Gigabit-LX described on 

page B-3

. 

Ca
ble
s 

Swi

tch Ports an

d Net

w

o

rk 

B-1 

Summary of Contents for J4861A































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands