HP J4861A Installation And Getting Started Manual Download Page 11

Page: 11 / 94

Introducing the HP ProCurve Series 4100gl Switches

Switch 4140gl.

The Switch 4140gl is available as a four slot chassis (J8151A)

with two 20-port Gig-T gl modules with 2 mini-GBIC Gig ports (J4908A)
preinstalled.

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Series 4100gl Switches

tro
duc

ing the

HP ProCurve

Switch 4160gl.

The Switch 4160gl (J8152A) is available as an eight slot

chassis with three 20-port Gig-T gl modules with 2 mini-GBIC Gig ports
(J4908A) preinstalled .

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

See “Switch Features” on

page 1-10

for a list of the switch modules that you

can install in the HP ProCurve Series 4100gl Switches (modules available
when this manual was printed).

With these switches you can build a switched network infrastructure by
connecting it to hubs, other switches, or routers, or you can connect
computers, printers, and servers to this switch to provide dedicated band-
width to those devices.

1-3

Summary of Contents for J4861A































































































Search results

Summary of Contents for J4861A

Reviews:

Brands by name

Popular brands

HP J4861A, Installation And Getting Started Manual

Search results

Summary of Contents for J4861A

Reviews:

Brands by name

Popular brands