manualshive.com logo in svg

HP J3108A, Installation Manual

Share
Download
HP J3108A Installation Manual Download Page 2

Hewlett-Packard Company
8000 Foothills Boulevard, m/s 5551
Roseville, California  95747-5551

http://www.hp.com/go/network_city

© 1996 Hewlett-Packard Company.
All Rights Reserved

Reproduction, adaptation, or translation without prior 
written permission is prohibited, except as allowed under 
the copyright laws.

Publication Number

J3108-90002
Edition 1
September 1996

Applicable Product

HP J3108A

Disclaimer

The information contained in this document is subject to 
change without notice.

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY 
OF ANY KIND WITH REGARD TO THIS MATERIAL, 
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS 
FOR A PARTICULAR PURPOSE.  Hewlett-Packard shall not 
be liable for errors contained herein or for incidental or 
consequential damages in connection with the furnishing, 
performance, or use of this material.

Hewlett-Packard assumes no responsibility for the use or 
reliability of its software on equipment that is not furnished 
by Hewlett-Packard.

Warranty

See the warranty card included with the product.

A copy of the specific warranty terms applicable to your Hewlett-
Packard product and replacement parts can be obtained from your 
HP sales and service office or HP-authorized reseller.

Summary of Contents for J3108A









































Reviews:

No comments

Brands by name

Popular brands

Load more brands