manualshive.com logo in svg

HP HP 830 Series, Installation Manual, Page: 49 / 58

Share
Download
HP HP 830 Series Installation Manual Download Page 49

 

45

 

LED Mark Status 

Description 

RPS status 
LED

 

RPS 

Steady green 

Both AC and DC inputs are normal. 

 

Steady yellow 

The AC input is abnormal or no AC input is 
present, while the DC input is normal. 

 

Off 

No DC input is present. 

 

10/100/10
00 Base-T 

Ethernet port 
status LED

 

N/A 

Steady green 

A 1000 Mbps link is present on the port. 

 

Flashing green (33 Hz) 

The port is receiving or transmitting data at 
1000 Mbps. 

 

Steady yellow 

A 10/100 Mbps link is present on the port. 

 

Flashing yellow (33 Hz) 

The  port is receiving or transmitting data at 

10/100 Mbps. 

 

Off 

No link is present on the port. 

 

Gigabit SFP 
port status 

LED 

N/A 

Steady green 

A 1000 Mbps link is present on the port. 

 

Flashing green (33 Hz) 

The port is receiving or transmitting data at 
1000 Mbps. 

 

Off 

No link is present on the port.

 

Expansion 
slot LED

 

MOD1 (or 
MOD2) 

Steady green 

An interface module is connected. 

 

Steady yellow 

The slot does not support the interface module 
installed in it. 

 

Flashing green  

The interface module is receiving or 
transmitting data. 

 

Flashing yellow  

The interface module has failed the POST.

 

Off 

No interface module is present in the slot, or the 
interface module is not connected. 

 

 

 

Summary of Contents for HP 830 Series



























































Reviews:

No comments