manualshive.com logo in svg

HP Deskpro 300, Hardware Reference Manual

Share
Download
HP Deskpro 300 Hardware Reference Manual Download Page 12

Compaq Deskpro Workstation 300 Hardware Reference Guide    

1-7

Compaq Confidential - Need to Know Required

Writer: M. Church Part Number: 212399-001 File Name: d-ch1.doc

Last Saved On: 09/07/00 2:03 PM Last Saved By: Integrity Group

7.  While holding the drive casing, gently pull the drive out of the

drive bay.

CAUTION:

  When removing a drive, do not pull the drive from the

front of the drive bay. To prevent damage to the drive bezel, push the
drive from the rear for removal from the front of the drive bay.

8.  After placing the workstation in the desktop position, gently slide

the drives back into the bay.

Installing the drives

CAUTION:

  The use of unnecessary force when installing the drive

may result in damage to the drive.

✎

Always place the diskette drive in the bay nearest the top of
the chassis (bay 3) in the desktop configuration to ensure
proper drive clearance and access. When all of the drives are
properly inserted, the drivelock will secure the drives in place.

9.  Reconnect the power and data cables to the drives as labeled.

Summary of Contents for Deskpro 300



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands