HP D530 - Compaq Business Desktop Reference Manual Download Page 42 | Manualshive

Page: 42 / 77

background image

Hardware Upgrades

Guide Screw Locations

The guide screws on a 3.5-inch diskette drive

1

are placed closer together than on

the hard drive

2

.

To install a drive into the bay:

1. If you have locked the Smart Cover Lock, use Computer Setup to unlock the

lock.

2. Turn off the computer properly through the operating system, then turn off any

external devices.

3. Disconnect the power cord from the power outlet and disconnect any external

devices.

4. Remove the computer access panel and front bezel.

2-32

Hardware Reference Guide

«
...
40
41
42
43
44
...
»

Summary of Contents for D530 - Compaq Business Desktop














































































Reviews:

No comments

Related manuals for D530 - Compaq Business Desktop

Veriteq viewLinc 4.0

Brand: Vaisala Pages: 168

Brand: MACROMEDIA Pages: 156

SENTINEL LOG MANAGER 1.0.0.5 - 03-31-2010

Brand: Novell Pages: 168

Mobility Services Platform 3.3.1

Brand: Motorola Pages: 28

IDEN COMPANIONPRO

Brand: Motorola Pages: 94

AIR-CB21AG-A-K9

Brand: Motorola Pages: 15

Brand: Motorola Pages: 43

Brand: Motorola Pages: 33

FREESCALE SEMICONDUCTOR M68EZ328ADS

Brand: Motorola Pages: 65

Mobility Services Platform 3.2

Brand: Motorola Pages: 68

IDEN WIRELESS DATA SERVICES

Brand: Motorola Pages: 116

Mobility Services Platform 3.2.1

Brand: Motorola Pages: 72

mobile PhoneTools

Brand: Motorola Pages: 12

Brand: Sanyo Pages: 132

Brand: Elgato Pages: 5

Brand: Vonamic Pages: 30

Xbox360 MotoGP08

Brand: Capcom Pages: 28

Brand: MINOLTA-QMS Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands