manualshive.com logo in svg

HP Compaq dx7200 MT, Reference Manual, Page: 61 / 216

Share
Download
HP Compaq dx7200 MT Reference Manual Download Page 61

Service Reference Guide, dx7200

390812-001

4–7

Serial and Parallel ATA Drive Guidelines and Features

4.9  Mixed Devices Boot and Drive Letter Ordering

SATA Emulation

Hard Drive Order

HDD Boot and Drive 

Letter Ordering

Separate IDE Controller 

(default). Used with Windows 

2000 and XP.

A. Integrated SATA
B. Integrated IDE

A1. SATA 0 
A2. SATA 2
A3. SATA 1 
A4. SATA 3
B1. IDE Device 0
B2. IDE Device 1

Separate IDE Controller. Used 

with Windows 2000 and XP.

A. Integrated IDE
B. Integrated SATA

A1. IDE Device 0
A2. IDE Device 1
B1. SATA 0
B2. SATA 2
B3. SATA 1
B4. SATA 3

Combined with IDE 

Controller. Used with 

Windows 9x, NT, and Linux.

A. Integrated SATA
B. Integrated IDE

A1. SATA 0 
A2. SATA 2
B1. IDE Device 0
B2. IDE Device 1

Combined with IDE 

Controller. Used with 

Windows 9x, NT, and Linux.

A. Integrated IDE
B. Integrated SATA

A1. IDE Device 0
A2. IDE Device 1
B1. SATA 0 
B2. SATA 2

Summary of Contents for Compaq dx7200 MT

























































































































































































































Reviews:

No comments