manualshive.com logo in svg

HP Compaq dx7200 MT, Reference Manual, Page: 197 / 216

Share
Download
HP Compaq dx7200 MT Reference Manual Download Page 197

Service Reference Guide, dx7200

390812-001

D–21

Troubleshooting Without Diagnostics

Diagnostics passes, but 

the computer does not 

communicate with the 

network.

Network drivers are not 

loaded, or driver 

parameters do not match 

current configuration.

Make sure the network drivers are 

loaded and that the driver 

parameters match the configuration 

of the network controller.
Make sure the correct network client 

and protocol is installed.

The network controller is 

not configured for this 

computer.

Select the 

Network

 icon in the 

Control Panel

 and configure the 

network controller.

Network controller 

stopped working when 

an expansion board was 

added to the computer.

Network controller 

interrupt is shared with an 

expansion board.

Under the Computer Setup 

Advanced

 menu, change the 

resource settings for the board.

The network controller 

requires drivers.

Verify that the drivers were not 

accidentally deleted when the 

drivers for a new expansion board 

were installed.

The expansion board 

installed is a network card 

(NIC) and conflicts with 

the embedded NIC.

Under the Computer Setup 

Advanced

 menu, change the 

resource settings for the board.

Network controller stops 

working without apparent 

cause.

The files containing the 

network drivers are 

corrupted.

Reinstall the network drivers, using 

the 

Restore Plus!

 CD.

The cable is not securely 

connected.

Ensure that the cable is securely 

attached to the network connector 

and that the other end of the cable 

is securely attached to the correct 

device.

The network controller is 

defective.

Replace the system board.

New network card will 

not boot.

New network card may be 

defective or may not meet 

industry-standard 

specifications.

Install a working, industry-standard 

NIC, or change the boot sequence 

to boot from another source.

Cannot connect to 

network server when 

attempting Remote 

System Installation.

The network controller is 

not configured properly.

Verify Network Connectivity, that a 

DHCP Server is present, and that 

the Remote System Installation 

Server contains the NIC drivers for 

your NIC.

System setup utility 

reports unprogrammed 

EEPROM.

Unprogrammed EEPROM.

Flash the ROM.

Solving Network Problems 

(Continued)

Problem

Cause

Solution

Summary of Contents for Compaq dx7200 MT

























































































































































































































Reviews:

No comments