HP Compaq dx2710 Microtower Service & Reference Manual Download Page 13

Page: 13 / 107

Service Reference Guide

483941-001

2–5

Setup Utilities and Diagnostics Features

Standard
CMOS
Features

(continued)

SATA Port 0
SATA Port 1
SATA Port 2
SATA Port 3

For each, allows you to:

• IDE Channel 0 Master (for SATA Port 0 Only)
• IDE Channel 1 Slave (for SATA Port 1 Only)
• detect HDD size and head on selected

channel

• set extended drive on selected channel to (for

SATA Port 2 and port 3 only):

• None
• Auto

• set access mode on selected channel to:

• CHS
• LBA
• Large
• Auto

• view:

• Capacity
• Cylinder
• Head
• Precomp
• Landing Zone
• Sector

Legacy Mode Support

(for SATA 0/1 ONLY)

Disable
Enable

Halt On

Allows you to set at:

• All Errors
• No Errors
• All but Keyboard
• All but Diskette
• All but Disk/Key

Advanced
BIOS Features

F11 Prompt

Allow you to enable or disable this feature.

Quick Power On Self Test

Disables/enables the system to skip certain
tests while booting.
Enabling this feature decreases the time
required to boot the system.

POST Delay Time (seconds)

Allows you to set a POST delay time to:

• 0 Sec
• 5 Sec
• 10 Sec
• 15 Sec
• 20 Sec

Computer Setup

(Continued)

Heading

Option

Description

✎

Support for specific Computer Setup options may vary depending on the hardware
configuration.

Summary of Contents for Compaq dx2710 Microtower












































































































Search results

Summary of Contents for Compaq dx2710 Microtower

Reviews:

Related manuals for Compaq dx2710 Microtower

Brands by name

Popular brands

HP Compaq dx2710 Microtower, Service & Reference Manual

Search results

Summary of Contents for Compaq dx2710 Microtower

Reviews:

Related manuals for Compaq dx2710 Microtower

Brands by name

Popular brands