HP Compaq d530 SFF Hardware Reference Manual Download Page 74 | Manualshive

Page: 74 / 79

background image

G-2

www.hp.com

Hardware Reference Guide

Routine Computer Care and Shipping Preparation

Optical Drive Precautions

Be sure to observe the following guidelines while operating or
cleaning the optical drive.

Operation

■

Do not move the drive during operation. This may cause it to
malfunction during reading.

■

Avoid exposing the drive to sudden changes in temperature, as
condensation may form inside the unit. If the temperature
suddenly changes while the drive is on, wait at least one hour
before you turn off the power. If you operate the unit
immediately, it may malfunction while reading.

■

Avoid placing the drive in a location that is subject to high
humidity, extreme temperatures, mechanical vibration, or direct
sunlight.

Cleaning

■

Clean the panel and controls with a soft, dry cloth or a soft cloth
lightly moistened with a mild detergent solution. Never spray
cleaning fluids directly on the unit.

■

Avoid using any type of solvent, such as alcohol or benzene,
which may damage the finish.

Safety

If any object or liquid falls into the drive, immediately unplug the
computer and have it checked by an authorized HP service provider.

«
...
72
73
74
75
76
...
»

Summary of Contents for Compaq d530 SFF
















































































Reviews:

No comments

Related manuals for Compaq d530 SFF

Personal Computer

Brand: IBM Pages: 318

CLP 600N - Color Laser Printer

Brand: Samsung Pages: 23

Brand: Wasp Barcode Technologies Pages: 69

Brand: Igel Pages: 2

Brand: UMAX Technologies Pages: 34

Brand: VISIONARY DESIGNS Pages: 2

Brand: Gigabyte Pages: 2

Brand: Advantech Pages: 94

Brand: IBM Pages: 194

Brand: Casio Pages: 133

Brand: Dell Pages: 72

Brand: Gateway Pages: 2

Brand: Gateway Pages: 98

Brand: Gateway Pages: 190

Brand: MSI Pages: 36

Brand: Cavalry Pages: 3

Brand: Fanvil Pages: 12

Brand: Fanvil Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands