manualshive.com logo in svg

HP A5120 EI Series, Command Reference Manual

Share
Download
HP A5120 EI Series Command Reference Manual Download Page 22

 

14 

  Unreachable:                     0 

  Source quench:                   0 

  Routing redirect:                0 

  Echo request:                    0 

  Router advert:                   0 

  Router solicit:                  0 

  Time exceed:                     0 

  IP header bad:                   0 

  Timestamp request:               0 

  Timestamp reply:                 0 

  Information request:             0 

  Information reply:               0 

  Netmask request:                 0 

  Netmask reply:                   0 

  Unknown type:                    0 

Table 2

 

Output description 

Field 

Description 

current state 

Current physical state of the interface, which can be 

 

Administrative DOWN: Indicates that the interface is 
administratively down. The interface is shut down with the 

shutdown

 command. 

 

DOWN: Indicates that the interface is administratively up but its 
physical state is down, which may be caused by a connection or 
link failure. 

 

UP: Indicates that both the administrative and physical states of 
the interface are up. 

Line protocol current state 

Current state of the link layer protocol, which can be 

 

DOWN: Indicates that the protocol state of the interface is down. 

 

UP: Indicates that the protocol state of the interface is up. 

 

UP (spoofing): Indicates that the protocol state of the interface 
pretends to be up; however, no corresponding link is present, or 
the corresponding link is not present permanently but is 
established as needed. 

Internet Address 

IP address of an interface followed by: 

 

Primary: Identifies a primary IP address. 

 

Sub: Identifies a secondary IP address. 

 

acquired via DHCP: Identifies an IP address obtained through 
DHCP. 

 

acquired via BOOTP: Identifies an IP address obtained through 
BOOTP. 

 

Cluster: Identifies a cluster IP address. 

 

Mad: Identifies a MAD IP address. 

Broadcast address 

Broadcast address of the subnet attached to an interface 

The Maximum Transmit Unit 

Maximum transmission units on the interface, in bytes 

input packets, bytes, multicasts 
output packets, bytes, multicasts 

Unicast packets, bytes, and multicast packets received on an 
interface (the statistics start at the switch startup) 

Summary of Contents for A5120 EI Series


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands