HP 9000 Model D280 Upgrade Manual Download Page 43 | Manualshive

Page: 43 / 68

background image

2-3

R Class System Memory Upgrade

Memory Installation Procedure

Memory Installation Procedure

A. Check Existing
System Memory

To check the memory configuration on your system:

Reboot the system by typing /etc/shutdown -r at the HP-UX system prompt:

/etc/shutdown -r

When prompted, halt the boot process by pressing any key on the keyboard:

Processor is booting from first available device.

To discontinue, press any key within 10 seconds.

Boot terminated.

Main Menu ----------------------------------------------------

Command     Description
-------     -----------
BOot [PRI|ALT|<path>]     Boot from specified path
PAth [PRI|ALT|CON|KEY] [<path>] Display or modify a path
SEArch [DIsplay|IPL] [<path>] Search for boot devices
TOC     Soft boot the system

COnfiguration [<command>]     Access Configurationmenu/commands
INformation [<command>]     Access Information menu/commands
SERvice [<command>]     Access Service menu/commands
DIsplay     Redisplay the current menu
HElp [<menu>|<command>]     Display help for menu or command
RESET     Restart the system

-------
Main Menu: Enter command >

«
...
41
42
43
44
45
...
»

Summary of Contents for 9000 Model D280





































































Reviews:

No comments

Related manuals for 9000 Model D280

Brand: Olivetti Pages: 118

Brand: Markant Pages: 11

Brand: A1Touch Pages: 8

Brand: Medion Pages: 2

Brand: WAGO Pages: 52

Brand: Matrox Pages: 174

Brand: Chipsee Pages: 21

Rosemount TankRadar SCC 5320

Brand: Emerson Pages: 4

Brand: Emerson Pages: 108

Brand: IBM Pages: 72

Brand: Datapath Pages: 14

LCD Computer and Touchscreen

Brand: Tek Panel Pages: 2

Brand: dynabook Pages: 124

Brand: CompuPro Pages: 64

Brand: CompuLab Pages: 25

UNO-3200G Series

Brand: Advantech Pages: 50

Brand: Advantech Pages: 52

Brand: Advantech Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands