manualshive.com logo in svg

HP 8719ES, Service Manual, Page: 42 / 52

Share
Download
HP 8719ES Service Manual Download Page 42

14-28

Service Guide

Assembly Replacement and Post-Repair Procedures

HP 8719ET/20ET/22ET

Removing the A3 Disk Drive Assembly

HP 8719ES/20ES/22ES

RF Network Analyzers

Removing the A3 Disk Drive Assembly

Tools Required

• T-8 TORX screwdriver

• T-10 TORX screwdriver

• T-15 TORX screwdriver

• small slot screwdriver

• ESD (electrostatic discharge) grounding wrist strap

Removal

1. Disconnect the power cord and remove the bottom and left side covers, refer to

“Removing the Covers” on page 14-6

.

2. Remove the front panel, refer to

“Removing the Front Panel Assembly” on page 14-8

.

3. Turn the instrument upside-down and disconnect the ribbon cable (item 1) from the

CPU board.

4. Remove the 4 screws (item 2) that secure the disk drive bracket to the side of the frame.

5. Slide the disk drive out of the instrument.

6. Remove the 4 screws (item 3) that secure the disk drive to the bracket.

Replacement

1. Reverse the order of the removal procedure.

Summary of Contents for 8719ES





















































Reviews:

No comments