manualshive.com logo in svg

HP 8719ES, Service Manual

Share
Download
HP 8719ES Service Manual Download Page 26

14-12

Service Guide

Assembly Replacement and Post-Repair Procedures

HP 8719ET/20ET/22ET

Removing the Display Lamp and Assembly

HP 8719ES/20ES/22ES

RF Network Analyzers

Removing the Display Lamp and Assembly

Tools Required

• T-10 TORX screwdriver

• T-15 TORX screwdriver

• small slot screwdriver

• ESD (electrostatic discharge) grounding wrist strap

• 5/16-inch open-end torque wrench (set to 10 in-lb)

Removal

1. Remove the front panel assembly (A1), refer to

“Removing the Front Panel Assembly”

on page 14-8

.

2. Remove the 2 ribbon cables between:

•  (Item 1) the inverter assembly (A20) and the front panel interface board (A2)

•  (Item 2) the inverter assembly (A20) and the display assembly (A18)

3. Remove the 3 screws (item 3) that attach the display cover to the front panel.

4. Lift the display from the front panel and remove the 2 screws (item 4) from the outside

of the display.

5. Pull the lamp (item 5) out with a curving side motion, as shown.

Replacement

1. Reverse the order of the removal procedure.

Summary of Contents for 8719ES





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands