HP 8000 - Elite Convertible Minitower PC Technical Reference Manual Download Page 76

Page: 76 / 114

7-2

www.hp.com

Technical Reference Guide

Power and Signal Distribution

Table 7-1 lists the specifications of the external supply.

NOTES:
Total continuous power should not exceed 135 watts. Total surge power (<10 seconds w/duty cycle < 5 %) should not exceed

170 watts.
[1] Using 100 VAC input. The output voltage is allowed to drop to a minimum of 15 VDC during the transient period.

7.3 SFF/CMT

Power

Distribution

The SFF and CMT form factors use a common power source power supply unit contained within
the system chassis. Figure 7-2 shows the block diagram for power generation in the SFF and
CMT.

NOTES:
Connectors not shown to scale.
All + and

–

values are VDC.

RTN = Return (signal ground)

Figure 7-2. SFF/CMT Power Distribution and Cabling, Block Diagram

Table 7-1.

USDT 135-Watt Power Supply Unit Specifications

Parameter

Input Line Voltage Range

90–265 VAC

Line Frequency

47–63 Hz

Input Current, Maximum load @ 90 VAC

2.4 A

Output Voltage

19.5 VDC

Output Current, nominal load

3.5 A

Output Current, maximum load

6.9 A

Output Current, peak load (300 ms max) [1]

9.0 A

Conn

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

RTN

–

12 V

+12 Vmain

+12 Vsb

FANcmd

Fan Speed

PS On

Pwr Good

RTN

+12 Vcpu

System Board

Power On

Power Control Logic, DC/DC Converter

Front Bezel

& Voltage Regulators

Fan

+12 Vcpu

Power Button

Spd

+12 Vmain

+12 Vsb

90 - 264 VAC

NOTE: Return (RTN or ground) not shown.

-12 V

Pwr

Good

Fan
Cmd

Power Supply Unit

Summary of Contents for 8000 - Elite Convertible Minitower PC



















































































































Search results

Summary of Contents for 8000 - Elite Convertible Minitower PC

Reviews:

Related manuals for 8000 - Elite Convertible Minitower PC

Brands by name

Popular brands

HP 8000 - Elite Convertible Minitower PC, Technical Reference Manual

Search results

Summary of Contents for 8000 - Elite Convertible Minitower PC

Reviews:

Related manuals for 8000 - Elite Convertible Minitower PC

Brands by name

Popular brands