HP 8000 - Elite Convertible Minitower PC Technical Reference Manual Download Page 25 | Manualshive

Page: 25 / 114

background image

Technical Reference Guide

www.hp.com

2-9

System Overview

2.3.9 Graphics Subsystem

These systems use the Q45 GMCH component, which includes an integrated graphics controller
that can drive both an external VGA monitor and a DisplayPort digital display. The controller
implements Dynamic Video Memory Technology (DVMT 3.0) for video memory. Table 2-5
lists the key features of the integrated graphics subsystem.

All systems include a legacy VGA connector and a DisplayPort connector and support dual
monitor operation. The DisplayPort includes a multimode feature that allows a DVI or VGA
adapter to be connected to the DisplayPort.

These systems also include two PCIe graphics slots (one x16, one x4/x16 connector) to ensure
full graphics upgrade capabilities.

2.3.10 Audio Subsystem

These systems use the integrated High Definition audio controller of the chipset and the ADI
ADL261 High Definition audio codec. HD audio provides enhanced audio performance with
higher sampling rates, refined signal interfaces, and audio processors with increased
signal-to-noise ratio. The audio line input jack can be re-configured as a microphone input, and
multi-streaming is supported. These systems include a 1.5-watt output amplifier driving an
internal speaker, which can be muted with the F10 BIOS control. All models include front
panel-accessible stereo microphone input and headphone output audio jacks.

Table 2-5

Integrated Graphics Subsystem Statistics

Q45 GMCH

Integrated Graphics Controller

Recommended for

Hi 2D, Entry 3D

Bus Type

Int. PCI Express

Memory Amount

32 MB pre-allocated

Memory Type

DVMT 3.0

DAC Speed

400 MHz

Maximum 2D Resolution

2048x1536 @ 85 Hz

Hardware Acceleration

Quick Draw,

DirectX 9,

Direct Draw,

Direct Show,

Open GL 1.45,

MPEG 1-2,

Indeo

Outputs

1 VGA, 1 DisplayPort 1.1 [see text]

«
...
23
24
25
26
27
...
»

Summary of Contents for 8000 - Elite Convertible Minitower PC



















































































































Reviews:

No comments

Related manuals for 8000 - Elite Convertible Minitower PC

TitraLab KF1000 Series

Brand: Hach Pages: 68

TitraLab AT1102

Brand: Hach Pages: 158

Brand: Harbor Freight Tools Pages: 4

Brand: Medion Pages: 2

POWERMATE - VERSION 2007

Brand: NEC Pages: 31

Brand: ECS Pages: 53

POWERMATE P - SERVICE 1996

Brand: NEC Pages: 178

Brand: Advantech Pages: 17

Brand: Antec Pages: 10

Brand: Quanmax Pages: 37

Brand: Arista Pages: 47

Brand: HP Pages: 4

Brand: HP Pages: 10

Brand: HP Pages: 10

Pavilion g3700 - Desktop PC

Brand: HP Pages: 1

Pavilion g3200 - Desktop PC

Brand: HP Pages: 1

Pavilion Elite m9280f

Brand: HP Pages: 2

Pavilion Elite m9170

Brand: HP Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands