HP 5998-1600 User Manual Download Page 10

 

switching chip. Typically, a management Ethernet port is used to connect 

a PC for loading system programs or debugging, or connect the remote 

network management station for implementing remote system 
management. 

Table 3

 

Management Ethernet port specifications 

Item Specification 

Connector type 

RJ-45 

Transmission rate 

10/100/1000 Mbps, half/full duplex  

Transmission medium and 
maximum transmission 

distance 

Category-5 twisted pair cable that supports a 
maximum transmission distance of 100 m (328.08 

ft) 

Services 

Upgrade of host software and BootWare, network 
management.  

 

Hardware specifications 

Table 4

 

OAP card hardware specifications  

Item Specification 

Remarks 

CPU 

MIPS, eight cores, 1 
GHz 

— 

Memory 2 

GB 

Avoid replacing the memory by 
yourself to prevent damage to the OAP 
card.  

Number of 

CF card 
interfaces 

on an OAP 

card and 

the 
supported 

specificatio

ns 

Provides one CF card 

interface and one 1 
GB CF card when 

shipped. 
Supports a CF card 
with a maximum 

capacity of 1 GB.  

To replace a CF card, make sure 

that the new CF card can 
accommodate the software to be 

loaded.  
For how to load and upgrade 
software version of the OAP card, 

see the related documents.  

 

Summary of Contents for 5998-1600
















Reviews: