HP 5830 series Installation Manual Download Page 57

Page: 57 / 66

Hot swappable fan trays

The switches use hot swappable fan trays for heat dissipation.

Table 14

describes the fan trays

available for these switches.

Table 14

Fan tray specifications

Item Specifications

Back-to-front airflow fan tray (JC692A) (for the 48G model/48G TAA model)

Fans

Four 40 × 40 × 28 mm (1.57 × 1.57 × 1.1 in) fans

Max fan speed

9500 R.P.M

Max airflow

40 cubic feet per minute (CFM)

Airflow direction

Back to front (fans blow air from the power supply side to the network port side.)

Max power
consumption

8.42 W

Min power
consumption

0.87 W

Documentation
reference

HP A5830AF-48G Fan Trays (JC692A & JC693A) User Guide

Front-to-back airflow fan tray (JC693A) (for the 48G model/48G TAA model)

Fans

Four 40 × 40 × 28 mm (1.57 × 1.57 × 1.1 in) fans

Max fan speed

9500 R.P.M

Max airflow

40 CFM

Airflow direction

Front to back (fans draw air from the network port side to the power supply side.)

Max power
consumption

8.42 W

Min power
consumption

0.87 W

Documentation
reference

HP A5830AF-48G Fan Trays (JC692A & JC693A) User Guide

Back-to-front airflow fan tray (JC695A) (for the 96G model/96G TAA model)

Fans

Five 60 × 60 × 38 mm (2.36 × 2.36 × 1.50 in) fans

Max fan speed

11000 R.P.M

Max airflow

135 CFM

Airflow direction

Back to front (fans blow air from the power supply side to the network port side.)

Max power
consumption

75.5 W

Min power
consumption

4.4 W

Documentation
reference

HP A5830AF-96G Fan Trays (JC695A & JC696A) User Guide

Summary of Contents for 5830 series



































































Search results

Summary of Contents for 5830 series

Reviews:

Related manuals for 5830 series

Brands by name

Popular brands

HP 5830 series, Installation Manual

Search results

Summary of Contents for 5830 series

Reviews:

Related manuals for 5830 series

Brands by name

Popular brands