HP 5500-24G-SFP EI TAA Installation Manual Download Page 65

Page: 65 / 69

Port mode LED (Mode)

status

Port LED status

Description

Flashing yellow (3 Hz)

POST has failed on the port.

Off

No link is present on the port.

Steady yellow (duplex
mode)

Steady green

The port is operating in full duplex mode. The port
status LED fast flashes when the port is sending or

receiving data.

Flashing yellow (3 Hz)

POST has failed on the port.

Off

No link is present on the port.

Interface card status LED

Table 21

Interface card status LEDs description

LED mark

Status

Description

MOD1
MOD2

Green

The interface card is in position and operating
correctly.

Flashing yellow

The switch does not support the interface card
model, or the interface card has failed.

Off

The expansion interface card slot is empty.

Summary of Contents for 5500-24G-SFP EI TAA






































































Search results

Summary of Contents for 5500-24G-SFP EI TAA

Reviews:

Related manuals for 5500-24G-SFP EI TAA

Brands by name

Popular brands

HP 5500-24G-SFP EI TAA, Installation Manual

Search results

Summary of Contents for 5500-24G-SFP EI TAA

Reviews:

Related manuals for 5500-24G-SFP EI TAA

Brands by name

Popular brands