HP 5500-24G-SFP EI TAA Installation Manual Download Page 64

Page: 64 / 69

Table 19

10/100/1000Base-T auto-sensing Ethernet port LEDs description

Port mode LED (Mode)

status

Port LED status

Description

Steady green (rate mode)

Steady green

The port is operating at 1000 Mbps. The port
status LED fast flashes when the port is sending or
receiving data.

Steady yellow

The port is operating at 10/100 Mbps. The port
status LED fast flashes when the port is sending or

receiving data.

Flashing yellow (3 Hz)

POST has failed on the port.

Off

No link is present on the port.

Flashing green (1 Hz) (PoE
mode, available only for

PoE switches)

Steady green

PoE power supply is normal.

Flashing green (1 Hz)

The device attached to the port requires power
higher than the maximum or currently available

PoE output power on the port.

Steady yellow

The port is experiencing a PoE failure.
The port is not supplying power, because the

device attached to the port is not a powered
device.

Flashing yellow (3 Hz)

POST has failed on the port.

Off

The port is not supplying PoE power.

Steady yellow (duplex
mode)

Steady green

The port is operating in full duplex mode. The port
status LED fast flashes when the port is sending or

receiving data.

Steady yellow

The port is operating in half duplex mode. The port
status LED fast flashes when the port is sending or

receiving data.

Flashing yellow (3 Hz)

POST has failed on the port.

Off

No link is present on the port.

SFP port status LED

Each SFP port has a status LED to show port operating status and activities. The port mode LED indicates
the type of information (for example, port rate or duplex mode) that the port LEDs are showing. You can

use the port LED mode switching button to change the type of displayed port information.

Table 20

SFP port LEDs description

Port mode LED (Mode)

status

Port LED status

Description

Steady green (rate mode) or
flashing green (1 Hz, PoE

mode)

Steady green

The port is operating at 1000 Mbps. The port

status LED fast flashes when the port is sending or
receiving data.

Steady yellow (available
only on the 5500 EI

switches)

The port is operating at 100 Mbps. The port status
LED fast flashes when the port is sending or

receiving data.

Summary of Contents for 5500-24G-SFP EI TAA






































































Search results

Summary of Contents for 5500-24G-SFP EI TAA

Reviews:

Related manuals for 5500-24G-SFP EI TAA

Brands by name

Popular brands

HP 5500-24G-SFP EI TAA, Installation Manual

Search results

Summary of Contents for 5500-24G-SFP EI TAA

Reviews:

Related manuals for 5500-24G-SFP EI TAA

Brands by name

Popular brands