background image

Dear Hoval customer,

In the Hoval calorifier/heat pump, you have purchased 

a product that is built to the highest quality standards 

using state-of-the-art technology.

• 

Please check the items delivered, to ensure that they 

match your order and that nothing is missing. Also check 

for  any  damage  incurred  during  transport  and  notify 

your installer or the nearest Customer Service centre 

if  necessary.  Claims  made  at  a  later  date  cannot  be 

accepted for insurance reasons.

• 

For the correct installation and operation of your heat 

pump, all applicable laws, regulations and standards, 

in  particular  the  regulations  set  down  by  the  relevant 

electricity  company,  must  be  observed.  In  case  of 

queries,  please  contact  your  installer  or  the  nearest 

Hoval Customer Service centre.

• 

Before commissioning, the installation must be inspected, 

and the system must be approved for use by the installer.

• 

To ensure safe, economical and trouble-free operation, 

only operate your Hoval heat pump in accordance with 

these operating instructions.

• 

The  heat  pump  may  only  be  used  for  the  purposes 

for  which  it  was  designed,  and  for  which  it  has  been 

approved by Hoval.

• 

Do  not  make  any  modifications  to  the  unit,  as  this 

will  invalidate  any  legal  claims.  Conversion  kits  must 

be installed and approved by the licensed installer or 

Hoval Customer Service.

•  In the event of a fault or damage, please contact 

Hoval Customer Service to inquire about the necessary 

repairs. It is essential to shut down the unit to prevent 

damage.

With  the  purchase  of  a  Hoval  product  you  also  obtain 

a comprehensive warranty, in accordance with our terms 

of sales and warranty.

With proper use, the ownership of your Hoval calorifier/

heat pump will be a pleasure, and above all will provide 

you with a reliable and economical source of hot water.

2. 

Safety instructions

Installation  and  service  work  on  heat  pumps  can  be 

dangerous, on account of high pressures, live parts and 

the location of the installation.

Heat  pumps  may  only  be  installed,  commissioned  and 

maintained by trained, qualified servicing staff.

When working on this unit, all safety instructions in the 

relevant documents, on adhesive labels or plates on the 

unit itself and all other safety precautions in force must 

be observed.

Caution

Before carrying out maintenance and 

service work, always unplug the unit from 

the mains.

3

4 215 949 / 00

SAFeTy InSTrUCTIOnS

Summary of Contents for CombiVal WPE















Reviews: