HouseWarmer HWDV080BDV(N,P)-1 Installation Instructions And Owner'S Manual Download Page 16 | Manualshive

Page: 16 / 48

background image

24632-0-0508

Page 16

2

SILICON-BASED

SEALANT

MOUNTING

PLATE

CAP

FLUE OUTLET

TUBE

AIR INLET

TUBE

Failure to position these parts in accordance with diagram

or failure to use only parts speciﬁcally approved with these

appliances may result in property damage or personal

injury.

3

INSTALLATION OF HOUSEWARMER PRODUCT

INSTALLATION AND ANY REPAIRS TO THIS APPLIANCE MUST BE DONE BY A QUALIFIED

SERVICE PERSON.

WARNING: Read the installation instructions thoroughly before cutting or drilling any holes for

installation.

WARNING: Do not remove any rating plates attached to the unit.

CLEARANCES TO COMBUSTIBLES

Allow clearances (for all models) to adjacent combustible con-

struction.

IMPORTANT:

A qualiﬁed service person must install this ap-

pliance. Installation must conform to local codes, or in the ab-

sence of local codes, with the latest edition of the National Fuel

Gas Code, ANSI Z223.1.

A qualiﬁed service person should be called to inspect this appliance annually.

Have all of your appliances checked annually.

INSTALLATION AND ASSEMBLY

«
...
14
15
16
17
18
...
»

Summary of Contents for HWDV080BDV(N,P)-1

















































Reviews:

No comments

Related manuals for HWDV080BDV(N,P)-1

*MH81405D Series

Brand: Goodman Pages: 48

Brand: SummerAire Pages: 8

Brand: SummerAire Pages: 14

Brand: Lennox Pages: 28

Brand: Carrier Pages: 6

Brand: Carrier Pages: 16

050-135 Series 120

Brand: Carrier Pages: 16

Brand: Airease Pages: 62

Brand: Fedders Pages: 32

Brand: United States Stove Pages: 56

Brand: ICP Pages: 64

SUPREME FEM10-M2401AM-A

Brand: ICP Pages: 20

Twinning Kit 16W72

Brand: Lennox Pages: 4

CARBOLITE GERO CFM 12/2

Brand: VERDER Pages: 42

CARBOLITE GERO CAF G5

Brand: VERDER Pages: 88

Brand: Rheem Pages: 36

Brand: HEIL Pages: 43

Brand: HEIL Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands