background image

Hotsy DB • 8.914-449.0 • Rev. 11/15

OPERATOR’S MANUAL   

   

PRESSURE WASHER

  

8

STEP 1:

 Attach the handle to the 

frame of the pressure washer.  

Note

: It may be necessary to move 

the handle supports from side to 
side in order to align the handle so it 
will slide over the frame supports.

STEP 2:

 Insert the carriage bolt 

through the holes from the outside 
of the unit and attach a nut from 
the inside of the machine. Tighten 
nuts.

STEP 3:

 Attach the spray gun/hose 

storage handle and bracket to 
handle. Tighten nuts.

STEP 4:

 Attach the high pressure 

hose to the spray gun using teflon 
tape on hose threads.

STEP 7:

 Release the coupler collar 

and push the nozzle until the collar 
clicks.  Pull the nozzle to make sure 
it is seated properly.

STEP 8:

 Connect the high pres-

sure hose to the pump discharge 
nipple. Push coupler collar forward 
until secure.

STEP 5:

 Attach nozzle extension 

to spray gun/wand.  Tighten both 
by hand.

STEP 6:

 Pull the spring-loaded col-

lar of the wand coupler back to insert 
your choice of pressure nozzle.

STEP 9:

 Connect (7.5m) garden 

hose to the cold water source.

ASSEMBLY INSTRUCTIONS

STEP 10: 

Check inlets filters, 

remove debris, then connect the 
garden hose to pump water inlet. 

 

 

CAUTION: Do not run the pump 

without water or pump damage 

will result.

Alignment 

Holes

Handle

Frame 

Assy.

Carriage 

Bolt

Nut

Studs

Nut

Hose/Gun  

Storage 

Bracket

Safety 

Latch

Spray 

Gun

High  

Pressure Hose

Nozzle Extension

Spray  

Gun/Wand

Wand 

Coupler

Pressure

Nozzle

Pressure 

Nozzle

Wand 

Coupler

Wand

Collar

Pump 

Discharge 

Nipple

High 

Pressure 

Hose

Cold 

Water 

Source

Garden 

Hose

Pump 

Water Inlet

Garden 

Hose

Coupler Collar

Bolts

Summary of Contents for DB-2323




















Reviews: